Research Projects Completed and Ongoing :

Sr. No. Title of the Project Principal Investigator Funding Agency Amount.
2005-06
01 Experimental test facility for investigation of enhancement in convection heat transfer coefficient using twisted pipe P. A. Patil
(Mechanical)
American Society of Heating, Refrigeration, and Air Conditioning Engineers 0.75

2006-07

01 Experimental test facility for investigation of enhancement in convection heat transfer coefficient using micro fin tape P. A. Patil
(Mechanical)
American Society of Heating, Refrigeration, and Air Conditioning Engineers 2.1
02 Liquid stabilization of alkaline protease Dr. S. P. Danao
(Chemical)
University of Pune 1.5
03 Application of two phase heat exchanger in chemical engineering S. U. Lokhande
(Chemical)
University of Pune 1.5
04 Corelation of field life degradation data with reliability prediction for mechatronic devices P. B. Kulkarni
(Chemical)
University of Pune 1.0
05 Continuous vacuum drying of agricultural products V. L. Gole
(Chemical)
University of Pune 1.0
 

2007-09

 

01 Utilization of industrial waste as fertilizer R. K. Lad
(Civil)
University of Pune 1.45
02 High performance network terminal user interface A. J. Kadam
(Computer)
University of Pune 1.0
03 Design development and simulation of multi level inverter for three phase induction motor A. A. Apte
(Electrical)
University of Pune 1.5
04 Implementation of variable speed adaptive delta modulated drive using digital signal processor K. B. Chaudhary
(Electronics)
University of Pune 1.5
05 Improvement of cluster performance using hard partition algorithm M. P. Sardey

(Electronics)

University of Pune 1.5
06 Upflow anaerobic sludge blanket reactor for waste water treatment Dr. J. D. Bapat

Dr. R. K. Tiwari

(Chemical)

University of Pune 2.0
07 Feasibility of biodiesel production from nagchampa Dr. R. K. Tiwari
V. L. Gole
(Chemical)
University of Pune 2.0
08 Design of bioreactor P. M. Warke
(Chemical)
University of Pune 1.0
 

2008-09

 

01 Enzymatic feasibility of biodiesel production from Nagchampa V. L. Gole

(Chemical )

The Institution of Engineers, India 0.25
 

2008-10

 

01 Development of latent heat storage for solar application: Water heating A. V. Waghmare

(Mechanical)

University of Pune 1.5
02 Evaluation and development of hybrid machining process of EDM and AJM S. H. Wankhede

V. Dholle

(Production)

University of Pune 1.25
03 Design, development, fabrication and evaluation of solar dryer for leafy vegetables Dr. S. K. Upasani
(Engg. Sci.)

Dr. M. S. Deshpande
(Engg.Sci)

Dr. S. P. Danao
(Chemical)

University of Pune 2.2
04 Ultrasonic measurement of lubrication film thickness D. Y. Dhande

O. A. More

M. Gajre

(Mechanical)

University of Pune 1.5
 

2009-10

 

01 Biodiesel production from nagchampa using cavitational techniques V. L. Gole

(Chemical )

The Institution of Engineers, India 0.40
 

2010-11

 

01 Biodiesel production from nagchampa using microwave irradiation V. L. Gole

(Chemical )

The Institution of Engineers, India 0.50
02 Purification of biodiesel using vacuum evaporator V. L. Gole

(Chemical )

The Institution of Engineers, India 0.50
 

2011-12

 

01 Degradation of Rhodmine  6G at pilot scale capacity using hybrid techniques based on cavitation A. V. Mohod

(Chemical )

The Institution of Engineers, India 0.20
 

2012-14

 

01 Synthesis of a new antituberculosis drug Dr. M. S. Deshpande (Engg. Science) University of Pune 3.00
02 3 D deformation measurement using sterio-vision for deep drawing operation on universal testing machine D. H. Joshi

(Production)

University of Pune 1.80
03 Biomass fermentation in 5 L stirring bioreactor S. B. Ghugare (Chemical) University of Pune 0.80
04 Reactive Distillation H. L. Kamble

(Chemical)

University of Pune 1.00
Total 5.60
 

2013-15

 

01 Evaluation of structural performance of reinforced concrete beams using glass fiber reinforced polymers. U. R. Awari (Civil) University of Pune 1.70
02 Development of eco-friendly model for removal of COx by using adsorbents. D. V. Wadkar (Civil) University of Pune 2.00
03 Design of classifier for detection of diabetes using soft computing. M. A. Pradhan

S. R. Nalamwar

(Computer)

University of Pune 1.40
04 Solar photovoltaic based thermo-electrical cooling systems for cars. V. V. Kulkarni (Electrical) University of Pune 2.20
05 Synthesis and characterization of M- and W- types of nano-ferrites. Dr. S. P. Danao

Dr. D. V. Nighot

(Engg. Science)

University of Pune 2.00
06 Process intensification and heterogeneous catalyzed. Dr. V. L. Gole

(Chemical)

AICTE New Delhi 1.50
Total 10.80
 

2014-16

 

01 Investigation of microwave sensor for non-invasive determination of blood glucose concentration. V. V. Deshmukh (Electronics) University of Pune 2.00
02 Experimental investigation on performance of SI engine fuelled with hydrogen gas as an alternative fuel. S. J. Navale (Mechanical) University of Pune 1.15
03 Study of earthquake induced waves in circular water tanks with various staging height. M. V. Waghmare

S. A. Kothari

(Civil)

University of Pune 2.00
04 Reinforced fly ash using different geosynthesis. V. N. Patil

(Civil)

University of Pune 2.00
05 Effect of amino acids on metal complexes non-linear optical signal crystals Dr. N. N. Shejwal

(Engg. Science)

University of Pune 2.10
06 Fabrication and manufacturing of water purifier A simple and economical way A.    V. Mohod

(Chemical)

The Institution of Engineers Kolkata India 0.25
Total 9.50

 

Research proposals submitted to BCUD during 2015-16:

SN Proposal No Principal investigator Department Project title
1 15ENG000521 L S Godse Electrical Effective implementation of super capacitor based system in electric vehicle
2 15ENG001657 V S Ponkshe Electrical Design and implementation of digitally controlled static VAR compensation system for low power application
3 15ENG001429 S k Biradar Electrical Design and development of battery ultra-capacitor hybrid energy source system for electric vehicle
4 15ENG001339  K S Padmaja Electrical Matrix converter and fed Brushless DC motor
5 15ENG000441 Dr S P Danao Chemical Value added product from Karanja using novel technique
6 15ENG000872 Dr M S Deshpande Chemical Studies of some novel anti-mycobacterium agents
7 15ENG000408 Dr V L Gole Chemical Process intensification of biodiesel synthesis from non- edible feedstock using hydrodynamic cavitation
8 15ENG000468 A V Mohod Chemical Effluent remediation by German-Indo based treatment technique supporting the cause of Mula and Mutha river Pune rejuvenation plan
9 15ENG000610 R S Raut Chemical Kinetics, optimization of fermentation parameters and scale up studies of processes for production of ethanol from molasses
10 15ENG000752 D W Gaikwad Computer Rule learner and multireading technique for real time intrusion detection system selection for high speed network
11 15ENG000780  N R Talhar Computer Video streaming techniques for reliable application over commutation framework architecture
12 15ENG000575 S V Athawale Computer Client server based intrusion prevention system for 802.11 wireless LANs
13 15ENG000389 S J Pachouly Computer Providing automated data security approach in public cloud based on ID-RDPC
14 15ENG000692  P P Vaste Elecronics Performance improvement of reconfigurable microstrip antenna with polarization diversity and radiation pattern selectivity
15 15ENG000860 V R Patil Mechanical Performance of diesel using preheated biodiesel.
16 15ENG000517  C S Choudhari Mechanical Design development and performance evaluation of a refrigeration system for environmental friendly refrigerant
17 15ENG000279 P S Aglawe Mechanical Automation for bone alignment in post-surgery monitoring and control for biomedical instrumentation
18 15ENG000631 C S Dharankar Mechanical  To develop a damper testing facility for the investigation of new damping mechanism and techniques for vehicle suspension
19 15ENG000891 M S Swami Mechanical Experimental investigation of auto rickshaw for back pressure effect on engine performance with optimum reduction in noise
20 15ENG001303  S H Wankhede Production Optimization of hybrid machining process of rotary electro discharge machining with abrasive media engineering